进口化工轴流泵(欧美进口十大品牌)

英国GRIMM格林进口化工轴流泵 UK GRIMM imported axial flow pump

英国GRIMM格林进口化工轴流泵概述： 

          进口化工轴流泵是英国格林自行研制开发的新产品，按口径分：250、300、350、450、500、600、700、800、900共9个型号，18个规格产品。可靠性好，维修方便，是专为氯碱、制盐中蒸发循环工程的特点而专门设计的轴流泵。借鉴了行业内的成功技术，并融入自身的设计所长，经优化的传动设计，运行振动小，噪音低，大幅提高了轴流泵的运行可靠性和平衡性，使维护周期和使用寿命大大增加。运行可靠性高，维护周期增加一倍以上，寿命增加20%。
          可输送化学中性和腐蚀性，冷的或热的，清洁的或污染的，悬浮液或有大量结晶颗粒的腐蚀性液体。

 

英国GRIMM格林进口化工轴流泵结构特点：
            参照升力线理论，吸取螺旋桨设计的经验，发展了沿径向变环量分布的轴流泵设计方法，并进行了厂内的模型试验，与同类型轴流泵相比，重量轻，体积小，刚性好，效率高(与英国格林第一代化工轴流泵相比，效率提高10%以上，重量减轻30%以上)。自驱动端看，泵为逆时针旋转。

英国GRIMM格林进口化工轴流泵设计特点： 
          进口化工轴流泵，采用悬臂式支撑型式，单级单吸轴流式叶轮，电机采用直联或皮带传动。采用后开门的结构，使得在检修或更换密封时，只要抽出转动部分即可，而不需要拆卸管路，因此具有维修方便的特点。密封型式可采用双端面机械密封或填料密封。泵体采用弯管式或蜗壳式结构，泵进出口口径相同。轴承箱体带有水冷腔，用以通冷却水冷却轴承。对于悬挂式结构或弹性基础式的轴流泵为特殊设计。

英国GRIMM格林进口化工轴流泵技术参数： 

 

 

流       量：200～12000m3/h          
扬       程：2～12m
转       速：580～1450r/min     
功       率：7.5～250KW
口       径：250～900mm 
设计压力：0.4MPa      
工作压力：1.0MPa
工作温度：-0～180℃

 

 

英国GRIMM格林进口化工轴流泵密封： 

密封腔处的径向振摆小于0.5mm，保证了密封的可靠性和耐久性，延长了维修周期。可以安装填料密封和单端或双端机械密封，并可安装动力密封以供特殊场合使用。

固定密封选用Viton等合成橡胶。

填料选用石棉、碳纤维、柔性石墨等优质耐腐减磨材料。

英国GRIMM格林进口化工轴流泵材质： 

         过流部件可用1Cr18Ni9，1Cr18Ni12Mo2Ti，1Cr18Ni12Mo3Ti，因科洛804等多种材质制造。输送温度为0～180℃的各种强腐蚀材质。

英国GRIMM格林进口化工轴流泵用途： 

            输送低温或高温液体；中性或有腐蚀的液体；清洁的或内含固体颗粒的液体。

特别适用于：
1、化工和石油化学工业

2、炼油厂、造纸厂、纸浆业、煤化工、发电厂、制药业、制糖业、炼钢厂、水处理

3、涂装行业(脱脂、磷化、电泳等工序)

UK GRIMM imported axial flow pump summary:

        imported chemical axial pump is a new product developed by Green in Britain. It is divided into 9 models and 18 specifications according to the caliber: 250, 300, 350, 450, 500, 600,, 700, 800, and 900. The utility model has the advantages of good reliability and convenient maintenance, and is an axial-flow pump specially designed for the characteristics of evaporation and circulation engineering in chlor alkali and salt making. Based on the success in the technology industry, and into the design director of itself, by driving the optimization design and operation of small vibration, low noise, greatly improves the reliability and balance of the axial flow pump, the maintenance period and the service life is greatly increased. The operation reliability is high, the maintenance cycle is more than doubled, and the service life is increased by 20%.

        A corrosive liquid capable of delivering chemical, neutral, corrosive, cold, or hot, clean or contaminated, suspended, or a large amount of crystalline particles.

UK GRIMM imported axial flow pump structure characteristics:

 

          According to the lifting line theory, draw propeller design experience, the development of the design method of axial flow pump with variable circulation distribution along the radial direction, and the model test is carried out and compared with the same type of axial flow pump has the advantages of small size, light weight, good rigidity, high efficiency (compared with the British first generation Green chemical axial flow the pump efficiency is increased by more than 10%, weight more than 30%). As viewed from the drive side, the pump rotates counter clockwise.

 

UK GRIMM imported axial flow pump design features:

 

           imported axial flow pump adopts cantilever support type, single stage single suction axial flow impeller. The motor adopts straight belt or belt drive. The utility model adopts the structure of a back door, so that when the seal is repaired or replaced, only the rotating part can be drawn out, and the pipe is not needed to be disassembled, so the utility model has the advantages of convenient maintenance. Sealing type can use double end mechanical seal or packing seal. The pump body adopts a bent pipe type or a volute type structure, and the inlet and outlet of the pump have the same caliber. The bearing housing is provided with a water cooling cavity for cooling the bearing by cooling water. For the suspension structure or elastic foundation type axial flow pump for the special design. 

UK GRIMM imported axial flow pump technical parameter:

 

 

 

 

 

Flow rate: 200 ~ 12000m3/h

Lift: 2 ~ 12m

Speed: 580 ~ 1450r/min

Power: 7.5 ~ 250KW

Caliber: 250 ~ 900mm

Design pressure: 0.4MPa

Working pressure: 1.0MPa

Operating temperature: -0 ~ 180 DEG C

 

UK GRIMM imported axial flow pump seal up:

 

 

The radial vibration pendulum at the sealing cavity is less than 0.5mm, which ensures the reliability and durability of the seal and prolongs the maintenance period. Packing seals and single or double end mechanical seals can be installed, and power seals can be installed for special occasions.

Viton and other synthetic rubber are used in the fixed seal.

Fillers are made of asbestos, carbon fiber, flexible graphite and other corrosion-resistant materials.

 

UK GRIMM imported axial flow pump texture of material:

 

           The flow components available 1Cr18Ni9, 1Cr18Ni12Mo2Ti, 1Cr18Ni12Mo3Ti, and other materials for colo 804 manufacturing. A variety of strong corrosion materials with a temperature of 0~180.

UK GRIMM imported axial flow pump purpose:

        imported axial flow pumps are mainly used in large flow and low lift occasions, especially for forced circulation processes with corrosive media. For example, the mandatory cycle of caustic soda and salt production is also applied to phosphate fertilizer, oil, chemical fiber, paper making, and other production sectors.